Motone UNDERTAKER Number Plate Bracket + PillBox License Plate Light

This Kit is designed to fit to the underside of your rear fender/mudguard - its especially useful in situations where you dont have alot of room to mount the plate - as well the angle you set the plate at has some adjustment so it can be used in custom applications. Besides that it is also designed to couple with our fender mount tail lights including the Reprobate Tail Light on top of the fender should you wish (Its especially useful for the reprobate as the undertaker is equipped with a license plate illumination light)  It comes the the Pillbox our billet license plate illumination light.   The footprint of the 3 holes used to mount the kit are the same we use on all our fenders, so if you have one of our fenders with the predrilled holes this will bolt on.

Motone STEALTH SLIDERS/ Adjustable Rear Indicator Turn Signal Brackets - Number Plate Mount

License Plate Mount Indicator Brackets - Low-Profile  Indicator brackets clamp onto the slots in your rear number plate bracket - that allow for a sliding fit so they can be adjusted to sit at the width of your number plate however wide or narrow that may be.  Indicators with M8 Threads only (ie ICON or PICO from us)  Made out of Stainless Steel and Powder Coated in Black

Motone The Clampits - 41mm - Indicator/Turn Signal Fork Mount Brackets - POLISHED

Ladies and Gentlemen these are the Clampits  - SOLD AS A PAIR   -  THIS VERSION IN POLISHED FINISH Built out of High Pressure Die Cast Aluminium these clamps wrap around your fork - in this case any 41mm fork - and you can bolt on your Indicator - they will work with Indicators that have 8 or 10mm sized threads (so any of the ones we make and most all of the ones out in the world)  Depending on your bike and the overall look you are going for you may wish to position your indicators at the front or rear side of the fork - these work either way around.  Other versions for other fork sizes are also in development  Common Bikes with 41mm Forks Include - Triumph Bonneville, T100, T120, Street Twin, Scrambler 900, Mag Wheel, Royal Enfield Interceptor, new Honda CB350, and many more 

Motone SIDEKICK SLIM (Axle-Mount) Side Mount Number Plate Kit (No Tail Light Version)(US SPEC VERTICAL PLATE)

Fits any LC 2016 and up Triumph Twin  SIDEKICK SLIM - This is the SLIM version for Vertical Orientation USA Spec License Plates  We have made several versions of this kit - this version includes a license plate light but no tail light, we also have a tail light version Kits Consists of Axle Plate Bracket - Forged Stainless Steel (MMU607) SLIM USA SPEC Side Mount Plate Mount Kit - Laser Cut Aluminium - Black Powder Coat (MMU618) The Pillbox - our E-Marked Street Legal Micro LED License Plate Light - 6061 Billet Aluminium and 120cm of wiring cable with 3.9mm bullet connector terminals  The Number plate itself mounts to Axle Plate Bracket using counter sunk screws which are provided - the plate has counter sunk holes at various levels so you can set it at a suitable height for the size of your number plate on your bike.  The Pillbox Light is designed to Plug and Play directly into any Motone rear wiring loom plug and play adapters For Example this one DDM016 for the BOBBER/Speedmaster/Scramber 1200/Speed Twin 1200 Eur4  Or For Street Twin/Speed Twin 900/T100/T120 this one DDM021 Or Speed Twin 1200 This one DDM017

Motone Sidekick (Axle-Mount) Side Mount Number Plate Kit (No Tail Light Version)

Fits all 2016 and UP Triumph Twins (Especially BOBBER/SPEEDMASTER/T120/T100LC/SPEED TWIN etc) We have made several versions of this kit - this version includes a license plate light but no tail light, we also have a tail light version Kits Consists of Axle Plate Bracket - Forged Stainless Steel (MMU607) Side Mount Plate Mount Kit - Laser Cut Aluminium - Black Powder Coat (MMU604) The Pillbox - our E-Marked Street Legal Micro LED License Plate Light - 6061 Billet Aluminium and 120cm of wiring cable with 3.9mm bullet connector terminals  The Number plate itself mounts to Axle Plate Bracket using counter sunk screws which are provided - the plate has counter sunk holes at various levels so you can set it at a suitable height for the size of your number plate on your bike.  The Pillbox Light is designed to Plug and Play directly into any Motone rear wiring loom plug and play adapters For Example this one DDM016 for the BOBBER/Speedmaster/Scramber 1200/Speed Twin 1200 Eur4  Or For Street Twin/Speed Twin 900/T100/T120 this one DDM021 Or Speed Twin 1200 This one DDM017

Motone The KLINGONS v2 - M8 Indicator Handlebar Mount Bracket Kit - PAIR

These are the KLINGONS - the idea of these is so that you can mount your Indicator (We recommend the PICO for these as they are small and lightweight) onto the underside of your handlebar. SOLD AS A PAIR (SET OF 2) - UPDATED VERSION 2.0  They come with a set of M4 stainless Socket Caps that replace the original M4 Bolts on the bars and provide enough length then mount the KLINGONS. Version 2.0 of these contains an extra L shaped bracket which adjusts the offset so that both indicators now end up in perfect symmetrical centre alignment with the headlight  We elected to use investment cast Stainless Steel to make the KLINGONS as they are so small the extra strength provided by using 300 series stainless means you can rest assured they will hold your Indicators on safely  We found that many Triumphs we looked at had M4 bolts on the bars on the control/perch brackets So far known to work on T120 / T100 / Bobber / Street Twin / Speed Twin 900 - will update more when we confirm 

Motone The Clampits - 41mm - Indicator/Turn Signal Fork Mount Brackets

Ladies and Gentlemen these are the Clampits  - SOLD AS A PAIR  Built out of High Pressure Die Cast Aluminium (we also have a similar version in Aluminum for you Americans) these clamps wrap around your fork - in this case any 41mm fork - and you can bolt on your Indicator - they will work with Indicators that have 8 or 10mm sized threads (so any of the ones we make and most all of the ones out in the world)  Depending on your bike and the overall look you are going for you may wish to position your indicators at the front or rear side of the fork - these work either way around.  Other versions for other fork sizes are also in development  Common Bikes with 41mm Forks Include - Triumph Bonneville, T100, T120, Street Twin, Scrambler 900, Mag Wheel, Royal Enfield Interceptor, new Honda CB350, and many more 

Motone L-CLAMPS Number/License Plate Bracket Rear Indicator/Turn Signal Mounts

New License Plate Indicator Brackets - the L-CLAMPS L shaped they clip into the slots that you would normally use to Bolt your Number Plate to the Plate Hanger/Bracket  Indicator brackets work with All Aftermarket Indicator out there  (8 or 10mm Thread no problem) Triumph OEM (Factory Original) Type Indicators  Includes blanking plates if not using the OEM holes Made out of Stainless Steel and Powder Coated in Black

Motone Shock Mount Indicator Brackets V2 - Work with all Indicators

New Shock mount 2.0 Indicator brackets will work on many different types makes and models of bikes with capability to mount any  Pretty much Any known Aftermarket Indicator out there  (8 or 10mm Thread no problem) Triumph OEM (Factory Original) Type Indicators  Can be fit on outside or inside of Shock depending on the type of shock you have - Includes blanking plates if not using the OEM holes.   Each bracket can be fit on either side of the bike  Made out of Stainless Steel and Powder Coated in Black

Motone Under Seat/Rear Frame Under Seat Indicator Brackets LC

These are the latest brackets we have made allowing you to fit indicators to the rear of your bike using the 2 bolt holes on either side at the top of your frame. These can be run in various combinations with our parts, depending on the rear mudguard of your bike and which make indicators you have and the length of threads they run As is we have designed the holes to bolt on using any  Indicators with 8mm Threads Indicators with 10mm Threads OEM Triumph LED Indicators As well as the above if you have a high and wide rear fender and want to fit with indicators that have particularly long threads, or you simply want to space your indicators our wider apart then you can fit this part in combination with our Billet Indicator Adapters ADT002 (for 8mm Indicators), or ADT003 (for 10mm Indicators) Fits Street Twin Street Cup Street Scrambler T100 LC T120   Note if you another accessory using these holes already it may still be possible to fit them both concurrently - use some washers under the seat latch to raise it up a few mm in this instance

Motone Indicator/Turn Signal Brackets - for LC Triumphs - 8mm

Motone Steel License/Number Plate Bracket Insert Round Light

Laser cut out of steel and powder coated Black these brackets are designed to work with the bolt spacing on any of our Round tail lights (Eldorado, Bel Air, Miller, Lecter, Cuda, etc)  You can use this bracket anywhere on the bike - or it also is designed to slide in between our fender light brackets and our tail lights in an assembly so you can mount a plate with them, with the down facing lights on the tail light illuminating the plate.  Often used in Combination with our Rear Mudguards etc Also check out the L-CLAMPS if you want to bolt some Indicators to the License Plate bracket 

Motone TRILINE Indicator/Turn Signal Ribbed Brackets - Top Shock Mount - Black

 

Motone TRILINE Indicator/Turn Signal Ribbed Brackets - Top Shock Mount - Brushed

 

Motone TRILINE Indicator/Turn Signal Ribbed Brackets - Top Shock Mount - Polish

 

Motone Indicator/Turn Signal Brackets - for LC Triumphs - 10mm

Motone Indicator Brackets - Top Shock Mount - Polished

 

Motone Indicator/Turn Signal Brackets - Top Shock Mount - Black